WE PUT THE ” E A S ” IN EASY

ADAS Calibration Information

ADAS Calibration Information

Section 1

**I-Car Repair standards require ADAS calibrations to be performed in the event of a collision on or near affected modules, when front bumper, rear bumper, windshield is removed. **

When Performing the ADAS calibrations, the required conditions need to be met in order to begin calibrations on all Makes/Models:

– Level/even floor space indoors free from all metal obstructions/structures with at least 6 meters/600cm/19ft of length and width of vehicle.

– In the event of a replacement of a new module (Front distance sensor, Blind spot module, windshield camera, various modules), keep old modules in order to pull stored configuration data, for configuration of new modules.

– In the event of replacement of Front windshield equipped with a Forward safety collision/Lane Watch Camera, an OEM windshield is recommended for proper camera positioning and calibration.

– Vehicle battery must be stable enough to hold a charge with a battery tender to avoid misreading’s and errors from modules.

– Calibration of front distance sensor, Windshield Camera, Parking sensors, and Blind spots are required in event of frontal or frontal-side impact in event of radar shifting, or removal of front/rear bumpers.

– Vehicle must have full size Tires/Wheels installed. No spare tires.

– Vehicle must be in drivable state to perform test drive under most calibration conditions.

Acura/Honda

*Front Millimeter Wave Radar/Cruise Control Distance Sensor*

  • – Specific Acura models can require up to 17ft of floor space in front of vehicle, with up to 6 ft of side clearance
  • – Requires the front bumper to be properly installed and fully secured to vehicle
  • – An OEM front grill emblem that is not damaged/scratched/dirty with the proper radar supported emblem for the Distance Sensor to send signals through.
  • – A new OEM front distance sensor in the event of a direct impact to front of vehicle.
  • – Calibration of front distance sensor in event of frontal or frontal-side impact in event of radar shifting.
  • – Calibration of front distance sensor when front bumper is removed/replaced.
  • – Proper vehicle 4-wheel alignment to ensure vehicle is not leaning, or has damaged components that will interfere with vehicle calibration
  • – Ensure Front radar mounting insert clips are new and or free from damage preventing proper seating/installation of radar.

*Front Mono/Multipurpose Windshield Camera*

  • – Requires OEM branded windshield for proper windshield camera bracket mounting positioning in order to ensure OEM specified targeting of lane reading and forward collision warning operation.
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – Up to 8 meters/800cm of open floor space
  • – New OEM windshield camera in even of direct windshield hit in camera area
  • – Calibration of windshield camera required when windshield is removed/replaced or involved in front end impact.
  • – Proper vehicle 4-wheel alignment to ensure vehicle is not leaning, or has damaged components that will interfere with vehicle calibration

*SRS/Airbag/Seat Weight Sensor*

  • – Must be calibrated whenever an SRS/ Airbag system component is replaced.
  • – In the event of an airbag deployment, the SRS module MUST be replaced with an OEM SRS/Airbag Module
  • – Level Floor space
  • – New OEM seat weight sensor in the event a passenger, or object was in passenger seat in the event of impact

*Parking Sensors*

  • – Required whenever Parking Sensor(s) are replaced
  • – Requires the correct OEM front and rear parking sensors.
  • – Front and rear bumpers to be installed on vehicle with sensors properly positioned in their correct locations.

*Blind Spot Modules*

  • – Requires calibration whenever blind spot modules are moved, removed, and replaced.
  • – Proper vehicle 4-wheel alignment to ensure vehicle is not leaning, or has damaged components that will interfere with vehicle calibration
  • – Requires OEM Mirrors to be installed with proper blind spot indicator package
  • – Rear bumper to be removed to perform blind spot monitor mounting and angle check.
  • – Level/even floor space indoors free from all metal obstructions/structures

*Passenger Mirror Lane View Camera system

  • – Requires OEM Passenger mirror with Lane View Camera system installed
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – up to 5ft behind and to the right side of vehicle
  • – Adequate lighting conditions that will not disrupt contrast/white balance of targeting system

FORD

*Front Smart Cruise Control Radar*

  • – A new OEM front distance sensor must be replaced in the event of a direct impact to front of vehicle.
  • – Front bumper must be removed in order to check Radar(s) for proper mounting/leveling. Front bumper must then be reinstalled to begin calibration.
  • – Calibration of front distance sensor is required in event of frontal or frontal-side impact in event of radar shifting.
  • – Calibration of front distance sensor when front bumper is removed/replaced.

*Front Mono/Multipurpose Windshield Camera*

  • – Requires OEM branded windshield for proper windshield camera bracket mounting positioning in order to ensure OEM specified targeting of lane reading and forward collision warning operation.
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – Up to 8 meters/800cm of open floor space
  • – New OEM windshield camera in even of direct windshield hit in camera area
  • – Calibration of windshield camera required when windshield is removed/replaced or involved in front end impact.
  •  

*SRS/Airbag/Seat Weight Sensor*

  • – Must be calibrated whenever an SRS/ Airbag system component is replaced.
  • – In the event of an airbag deployment, the SRS module MUST be replaced with an OEM SRS/Airbag Module
  • – Level Floor space
  • – New OEM seat weight sensor in the event a passenger, or object was in passenger seat in the event of impact

*Parking Sensors*

  • – Required whenever Parking Sensor(s) are replaced
  • – Requires the correct OEM front and rear parking sensors.
  • – Front and rear bumpers to be installed on vehicle with sensors properly positioned in their correct locations.

*Blind Spot Modules*

  • – Requires programming/Calibration of new OEM blind spot modules.
  • – Requires OEM Mirrors to be installed with proper blind spot indicator package.

GM (Chevrolet/Cadillac/Buick/GMC)

*Front short range/Long Range Radars*

  • – A new OEM front distance sensor must be replaced in the event of a direct impact to front of vehicle.
  • – Front bumper must be removed in order to check Radar(s) for proper mounting/leveling. Front bumper must then be reinstalled to begin calibration.
  • – Calibration of front distance sensor is required in event of frontal or frontal-side impact in event of radar shifting.
  • – Calibration of front distance sensor when front bumper is removed/replaced.

*Front Mono/Multipurpose Windshield Camera*

  • – Requires OEM branded windshield for proper windshield camera bracket mounting positioning in order to ensure OEM specified targeting of lane reading and forward collision warning operation.
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – Up to 8 meters/800cm of open floor space
  • – New OEM windshield camera in even of direct windshield hit in camera area
  • – Calibration of windshield camera required when windshield is removed/replaced or involved in front end impact.

*SRS/Airbag/Seat Weight Sensor*

  • – Must be calibrated whenever an SRS/ Airbag system component is replaced.
  • – In the event of an airbag deployment, the SRS module MUST be replaced with an OEM SRS/Airbag Module
  • – Level Floor space
  • – New OEM seat weight sensor in the event a passenger, or object was in passenger seat in the event of impact

*Parking Sensors*

  • – Required whenever Parking Sensor(s) are replaced
  • – Requires the correct OEM front and rear parking sensors.
  • – Front and rear bumpers to be installed on vehicle with sensors properly positioned in their correct locations.

*Blind Spot Modules*

  • – Requires programming/Calibration of new OEM blind spot modules.
  • – Requires OEM Mirrors to be installed with proper blind spot indicator package.

Hyundai/Kia

*Front Radar Distance Sensor*

  • – A new OEM front distance sensor must be replaced in the event of a direct impact to front of vehicle.
  • – Front bumper must be removed in order to check Radar(s) for proper mounting/leveling. Front bumper must then be reinstalled to begin calibration.
  • – Calibration of front distance sensor is required in event of frontal or frontal-side impact in event of radar shifting.
  • – Calibration of front distance sensor when front bumper is removed/replaced.
  • – Proper vehicle 4-wheel alignment/Calibration of steering angle sensor to ensure vehicle is not leaning, or has damaged components that will interfere with vehicle calibration

*Front Mono/Multipurpose Windshield Camera*

  • – Requires OEM branded windshield for proper windshield camera bracket mounting positioning in order to ensure OEM specified targeting of lane reading and forward collision warning operation.
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – Up to 8 meters/800cm of open floor space
  • – New OEM windshield camera in even of direct windshield hit in camera area
  • – Calibration of windshield camera required when windshield is removed/replaced or involved in front end impact.
  • – Proper vehicle 4-wheel alignment to ensure vehicle is not leaning, or has damaged components that will interfere with vehicle calibration

*SRS/Airbag/Seat Weight Sensor*

  • – Must be calibrated whenever an SRS/ Airbag system component is replaced.
  • – In the event of an airbag deployment, the SRS module MUST be replaced with an OEM SRS/Airbag Module
  • – Level Floor space
  • – New OEM seat weight sensor in the event a passenger, or object was in passenger seat in the event of impact

*Blind Spot Modules*

  • – Requires programming/Calibration of new OEM blind spot modules.
  • – Proper vehicle 4-wheel alignment to ensure vehicle is not leaning, or has damaged components that will interfere with vehicle calibration
  • – Requires OEM Mirrors to be installed with proper blind spot indicator package.
  • – Rear bumper to be removed to perform blind spot monitor mounting and angle check.

Infiniti/Nissan

*Front Radar Distance Sensor*

  • – A new OEM front distance sensor must be replaced in the event of a direct impact to front of vehicle. (Please save old module!)
  • – Front Bumpers must be fully and properly secured to vehicle with the correct Radar emblem installed that is not damaged.
  • – Proper vehicle 4-wheel alignment/Calibration of steering angle sensor to ensure vehicle is not leaning, or has damaged components that will interfere with vehicle calibration, calibration is dependent on LF or RF wheel alignment angle.
  • – For front ICC/Distance/Emergency Braking sensors require either a drive on alignment rack, or frame machine due to required target height distances for radar calibration
  • – Calibration of front distance sensor is required in event of frontal or frontal-side impact in event of radar shifting.
  • – Calibration of front distance sensor when front bumper is removed/replaced.

*Front Mono/Multipurpose Windshield Camera*

  • – Requires OEM branded windshield for proper windshield camera bracket mounting positioning in order to ensure OEM specified targeting of lane reading and forward collision warning operation.
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – Up to 8 meters/800cm of open floor space
  • – New OEM windshield camera in even of direct windshield hit in camera area. (Please save old module!)
  • – Calibration of windshield camera required when windshield is removed/replaced or involved in front end impact.
  • – Proper vehicle 4-wheel alignment to ensure vehicle is not leaning, or has damaged components that will interfere with vehicle calibration

Mazda

*Front Radar Distance Sensor*

  • – A new OEM front distance sensor must be replaced in the event of a direct impact to front of vehicle.
  • – Front Bumpers must be fully and properly secured to vehicle with the correct Radar emblem installed that is not damaged.
  • – Calibration of front distance sensor is required in event of frontal or frontal-side impact in event of radar shifting.
  • – Calibration of front distance sensor when front bumper is removed/replaced.

*Front Mono/Multipurpose Windshield Camera*

  • – Requires OEM branded windshield for proper windshield camera bracket mounting positioning in order to ensure OEM specified targeting of lane reading and forward collision warning operation.
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – Up to 8 meters/800cm of open floor space
  • – New OEM windshield camera in even of direct windshield hit in camera area
  • – Calibration of windshield camera required when windshield is removed/replaced or involved in front end impact.

*SRS/Airbag/Seat Weight Sensor*

  • – Must be calibrated whenever an SRS/ Airbag system component is replaced.
  • – In the event of an airbag deployment, the SRS module MUST be replaced with an OEM SRS/Airbag Module
  • – Level Floor space
  • – New OEM seat weight sensor in the event a passenger, or object was in passenger seat in the event of impact

*Blind Spot Modules*

  • – Requires programming/Calibration of new OEM blind spot modules.
  • – Requires OEM Mirrors to be installed with proper blind spot indicator package.
  • – Rear bumper to be installed to perform blind spot angle check.

Subaru

*Eyesight Windshield Camera*

  • – Requires OEM branded windshield for proper windshield camera bracket mounting positioning in order to ensure OEM specified targeting of lane reading and forward collision warning operation.
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – Up to 8 meters/800cm of open floor space
  • – New OEM windshield camera in even of direct windshield hit in camera area
  • – Calibration of windshield camera required when windshield is removed/replaced or involved in front end impact.

*Blind Spot Module*

  • – Requires programming/Calibration of new OEM blind spot modules.
  • – Requires OEM Mirrors to be installed with proper blind spot indicator package.
  • – Rear bumper to be installed to perform blind spot angle check.
  • – Calibration required in the event of collision/repairs to blind spot area that requires blind spots to be removed and installed

Toyota

*Front Millimeter Wave Radar*

  • – Requires the front bumper to be properly installed and fully secured to vehicle
  • – An OEM front grill emblem that is not damaged/scratched/dirty with the proper radar supported emblem for the Distance Sensor to send signals through.
  • – A new OEM front distance sensor in the event of a direct impact to front of vehicle.
  • – Calibration of front distance sensor in event of frontal or frontal-side impact in event of radar shifting.
  • – Calibration of front distance sensor when front bumper is removed/replaced.
  • – Ensure Front radar mounting insert clips are new and or free from damage preventing proper seating/installation of radar.

*Front Mono/Multipurpose Windshield Camera*

  • – Requires OEM branded windshield for proper windshield camera bracket mounting positioning in order to ensure OEM specified targeting of lane reading and forward collision warning operation.
  • – Level/even floor space indoors free from all metal obstructions/structures
  • – Up to 8 meters/800cm of open floor space
  • – New OEM windshield camera in even of direct windshield hit in camera area
  • – Calibration of windshield camera required when windshield is removed/replaced or involved in front end impact.

*Parking Sensors*

  • – Required whenever Parking Sensor(s) are replaced
  • – Requires the correct OEM front and rear parking sensors.
  • – Front and rear bumpers to be installed on vehicle with sensors properly positioned in their correct locations.

*Blind Spot Modules*

  • – Requires calibration whenever blind spot modules are moved, removed, and replaced.
  • – Requires OEM Mirrors to be installed with proper blind spot indicator package
  • – Rear bumper to be installed to perform blind spot monitor angle check.
  • – Level/even floor space indoors free from all metal obstructions/structures

==For all other Vehicle Makes and models, please give us a call to confirm your calibration needs and requirements!

Menu